Mother

Mother's Ideas On Customizing My Vee-String Female Prosthesis

Below you will see photos and steps on how I've made my Vee-String able to be put on like a pair of panties or a thong. I bought a Latex Repair Kit from Castle Supply and some crazy glue. I now have made the strings in permanent knots that fit to my body just fine. I can wear my Bladder Vee-String for a long time and the string doesn't hurt me. THANKS Castle.

*Click on the pics and they will expand to the right

Here's how I did it:

First, I have a 38" waist and I would normally use a large product. After my buying my Original Vee-String™, I decided to buy an Extra Large product to get more coverage of my genitals with my Bladder Vee-String. If you have a large "package", you might want to consider going up a product size (i.e. - small to a medium, medium to a large, etc.) If you are going to use the method below, the waist size won't matter to you.

I put the Vee-String on and tied it like they instructed, assuring it was a proper fit on me. I then marked about 1/4 inch from the knots on all three strings with a felt marker. I took it off like a pair of panties. I then cut the glued string undoing the loop and untied all of the knots on the strings.

I then cut the surgical tubing from the Repair Kit to the appropriate sizes by laying it out along the strings. I cut 3 lengths from the edges of the latex to the reference points on the strings. Once this was done, I had 3 pieces of tubing.

I then fished the string through the tubing. This can be done with a thin wire or small string attached to the end of the string and pulling through the tubing.

This is what the strings should look like once the tubing is on the strings.

Do not cut any of the strings for length yet...I used some household clamps to hold the tubing away from the marks on the strings. Push the tubing up the strings so at least 1" of string shows outside the tubing.

Line up the marks on the two waist strings.

Use the string in the repair kit and wrap it around the marks on the strings and tie a very tight knot. You might want to do this two times to make sure it is good and tight.

This is what it should look like once it is tied.

Trim off the excess strings. You should have a strong knot on the waist band.

You can now take off the clamps from the waist strings and let the tubing go into place up to the knot.

Use some crazy glue and liberally glue the string & knot. Do not get the glue on the tubing.

Now, take the gaffe string and take it under the waist string and over the top in the area where the new knot is tied. Make sure the clamp keeps the tubing away from the area to be tied.

Tie the strings together as you did for the waist.

Trim off any excess strings that are left outside the tubing.

Your knots should look something like this.

Crazy glue the knots once again.

Once the glue is dry, make sure the tubing is up and in place as measured.

This is what it should look like.

Powder yourself, the tubing and the product liberally. Try it on to make sure it fits and the knots hold correctly. Pull it up like a pair of panties, making sure the strings are in the correct place.

Place your penis inside the bladder (if you have one with that option). And adjust it to look correct on you.

Rear view of what it should look like.

Front view of the Vee-String. Notice that the skin tone on the latex appears to be a lot lighter when using flash photography even when it is a good match.

Once I was sure the product fit correctly and the strings were tied well, I then took off the Vee-String and used some of the latex that came with the Repair Kit to coat the knots. You can use this liberally, but make sure it dries before you put it back on.

That is how I did it. Hope this helps you as much as it has helped me.

Mother

	I put the Vee-String on and tied it like they instructed, assuring it was a proper fit on me. I then marked about 1/4 inch from the knots on all three strings with a felt marker. I took it off like a pair of panties. I then cut the glued string undoing the loop and untied all of the knots on the strings.
	I then cut the surgical tubing from the Repair Kit to the appropriate sizes by laying it out along the strings. I cut 3 lengths from the edges of the latex to the reference points on the strings. Once this was done, I had 3 pieces of tubing.
	I then fished the string through the tubing. This can be done with a thin wire or small string attached to the end of the string and pulling through the tubing.
	This is what the strings should look like once the tubing is on the strings.
	Do not cut any of the strings for length yet...I used some household clamps to hold the tubing away from the marks on the strings. Push the tubing up the strings so at least 1" of string shows outside the tubing.
	Line up the marks on the two waist strings.
	Use the string in the repair kit and wrap it around the marks on the strings and tie a very tight knot. You might want to do this two times to make sure it is good and tight.
	This is what it should look like once it is tied.
	Trim off the excess strings. You should have a strong knot on the waist band.
	You can now take off the clamps from the waist strings and let the tubing go into place up to the knot.
	Use some crazy glue and liberally glue the string & knot. Do not get the glue on the tubing.
	Now, take the gaffe string and take it under the waist string and over the top in the area where the new knot is tied. Make sure the clamp keeps the tubing away from the area to be tied.
	Tie the strings together as you did for the waist.
	Trim off any excess strings that are left outside the tubing.
	Your knots should look something like this.
	Crazy glue the knots once again.
	Once the glue is dry, make sure the tubing is up and in place as measured.
	This is what it should look like.

	Powder yourself, the tubing and the product liberally. Try it on to make sure it fits and the knots hold correctly. Pull it up like a pair of panties, making sure the strings are in the correct place.
	Place your penis inside the bladder (if you have one with that option). And adjust it to look correct on you.
	Rear view of what it should look like.
	Front view of the Vee-String. Notice that the skin tone on the latex appears to be a lot lighter when using flash photography even when it is a good match.
	Once I was sure the product fit correctly and the strings were tied well, I then took off the Vee-String and used some of the latex that came with the Repair Kit to coat the knots. You can use this liberally, but make sure it dries before you put it back on.